pin contact
英 [pɪn ˈkɒntækt]
美 [pɪn ˈkɑːntækt]
网络 插针; 针式接头; 管脚触点; 插针接触件
双语例句
- This test procedure may apply to any type or combination of current carrying members such as pin and socket contacts, relay contacts, wire and crimp connectors, or printed circuit board and contact.
这个测试程序适用任何类型象针脚，插座，继电器，电线，连接器，印刷电路板等电流通道载体或其结合体。 - Sleeve joint secures more than a pin joint, it's surface contact with the rim's inner wall is increased yet we're able to maintain it's lightweight properties.
袖套连接比销钉连接更加安全，可靠。这种表面与轮圈内部墙的接触更加增加了我们能维持它的轻量的特性。 - Note that die length of ejector pin contact with the mould plate is kept to a minimum by incorporating a clearance diameter hole in the mould plate.
注意，顶杆和模板的接触长度通过在模板中加工一个放大直径的孔来保持最小。 - Also the influence of piston impact force are discussed which including engine rotate speed, piston pin offset, clearance between piston and cylinder, piston mass and contact strength of piston surface.
并分别讨论了发动机转速，活塞销偏置量、活塞与气缸的间隙量、活塞质量以及活塞表面接触刚度对活塞碰撞冲击力的影响。 - Software I DEAS and MARC were used to calculate the thread face contact stress during the make up process, and to analyze the effect of taper mutation of pipe ( pin thread) and coupling ( box thread) on the thread face contact stress quantitatively.
利用I－DEAS和MARC软件计算了拧接过程螺纹齿面的接触应力，定量分析了管体（公螺纹）和管接箍（母螺纹）的锥度变化对齿面接触应力的影响。 - This paper puts forward an elastic pin model considering the deformation of pin and the effect of friction in contact areas.
本文提出一个计及轴销变形与接触区摩擦效应的弹性轴销模型，并采用弹性理论的复变函数解法，研究了正交各向异性无限大板的孔销接触问题。 - In this paper, two different restrict boundary conditions are adopted in Finite Element Analyze of connecting rod assembly, the stiff restrict of adopting crank pin and elastic restrict of crank. The contact cell applied with I DEAS Master Series 7.0 is used.
在对连杆组件进行有限元静力分析中，采用了两种不同的约束边界条件&刚性约束（即采用曲柄销约束）和弹性约束（即采用曲拐约束）。 - The results show that there are the continuous deformation contact phenomena and heterogeneous wear phenomena between the axle box with axle pin of the clearance joint, these phenomena make the amounts of dynamic wear larger where the continuous deformation contact occurs.
计算结果表明副元素间呈现出连续弹性变形现象，在连续变形接触处，动态磨损量较大使磨损加剧，并出现非均匀磨损。 - The process of interference-fit between swage-locking pin and composite laminate has been analyzed by introducing the static state contact arithmetic.
在分析过程中采用静态接触算法模拟环槽铆钉与复合材料板的干涉配合过程。 - The two-dimensional and three-dimensional contact stress simulation analysis of the pin on disc contact couple were carried by the ANSYS software.
利用ANSYS软件分别对销盘接触副进行二维和三维的接触应力模拟分析。 - Shijiazhuang Branch of China Unicom recently launched "Liang Pin Pai, Shu Xing Xiang"( hereinafter referred to as" Liang Shu") action, aiming to grasp the key aspects influencing customer perception and key point of contact facing customer, to enhance broadband service quality.
中国联通石家庄市分公司近期启动亮品牌、树形象（以下简称亮树）行动，着力把握影响客户感知的关键环节和直接面对客户的关键接触点，全面提升宽带服务质量。